Archives

2-2. How to setup SNOW-1 app

  1. Install the SNOW-1 App (go to the App Store and search “snow-1” to download) and launch the app, initial set up will start. Press the [START] button.
    snow1_setup1
  2. Follow the instructions and turn on the left binding (press and hold the power button for 3sec). The blue led will light up and you will see your device id in the app, select the correct device id.
    Note: If there are two or more SNOW-1 nearby (e.g. when you are in snowboard park with your friends), turn them on one by one as you cannot distinguish device id from the binding.
    snow1_setup2
    snow1_setup3
  3. Once the left binding is connected proceed to the next step.
    snow1_setup4
  4. Turn on the right binding power and do the same as in step 2.
    snow1_setup4.5
    snow1_setup5
  5. When both the right and left binding are connected correctly in the app, press [Go to next].
    snow1_setup6
  6. Select your weight, you can select 1-100kg and can change this anytime after initial set up.
    snow1_setup77. The message [Setup is complete] will be displayed, next follow the instructions for calibration.
    snow1_setup8

2-1. How to setup SNOW-1

  1. Remove the rubber cover for the connector on the bottom side of SNOW-1 and insert the flex sensor cable into the connector until you hear a click. Be careful not to use excessive force when inserting the cable to avoid damaging it.
  2. Insert the cable into the cable guide notch and then reattach the rubber cover firmly.


  3. Adjust the binding to your preferred angle, centering and stance width (distance between both bindings). You may want to ask snowboard shop or other professional for your best position.
  4. Set the center disc (with screw and washer) and screw to the board firmly. Make sure the micro USB connector (for battery charging) is covered with the rubber cap.
  5. Set the sole plate (with sole plate screw) and screw to the binding firmly.
  6. Attach the flex sensor (using the included double-sided tape) to center line of the board.

1-3. Terms and Conditions/Specifications

Important notice

This manual will provide you with important information on assembly, usage and maintenance.

Read the quick set up guide and warranty card included with this product carefully before you begin snowboarding with SNOW-1.

Please read this manual carefully and follow all instructions. This is in your interest and for your own safety. Snowboarding is a dangerous leisure activity that may lead to grave injures or death.

  • These bindings should be used exclusively for snowboarding on snow.
  • These bindings are not equipped with a crash release. When not riding please ensure one foot remains unclipped.
  • If the product is visibly damaged discontinue use.
  • Before every ride, make sure that all screws and/or levers on the board bindings are tightened securely.
  • Use these bindings exclusively with soft boots.
  • These bindings can only be mounted on snowboards with a 4×2 or 4×4 hole pattern.
  • Do not open the rubber cap(for a usb connector and for a flex sensor) when wet.
  • Please wipe off any moisture with a dry cloth before opening the rubber cap.
  • Do not use a higher voltage power adapter than the recommended maximum.
  • Make sure to insert connectors in the correct direction.
  • Lay flat snowboard when the battery charging.
  • Weight limit approx. 100kg
    Maximum impact limit approx. 180kg
    Do not apply more than 180kg of force to the product.
    If the product is damaged by impacts or collisions the warranty will be void.

Care and maintenance

  • After use, store the product in a dry room at room temperature. Make sure that it is not exposed to direct sunlight or high temperatures.
  • After you have finished reading please store this manual in a safe, easily accessible place.

Supported devices

SNOW-1 is compatible with iPhone®(5S and above)/iPad®/iPod touch®(5th generation and above) devices which support Bluetooth® LE and are running iOS8.4.1 or greater.

Size guide

XON SNOW-1 in L(*1), M(*2) and S(*3) sizes. Each SNOW-1 size is designed to fit the soft boot sizes listed below. Cerevo is unable to guarantee compatability with every boot.
*1 L Size – EUR 43-48, US 10.5-15, UK 9.5-14, JP 27.5-31cm
*2 M Size – EUR 42-45, US 9-12, UK 8-11, JP 26-28.5cm
*3 S Size – EUR 40.5-43, US 7.5-10, UK 6.5-9, JP 25-27cm

Specifications

 

  • Bluetooth 4.0 (Low Energy)
  • 9-axis sensors (acceleration, angular velocity, geomagnetism)
  • Dual flex sensors
  • 4 pressure sensors on each binding
  • 2 high luminance LEDs on each binding
  • Dimensions – W320xD175xH275 mm
  • Weight – 3.2kg (1 set)
  • Continuous operating time – 7 hours (may change depending on temperature and LED activation duration)
  • Charging time – 3 hours
  • Charging port – Micro USB
  • Waterproof – IPX4 Certified
  • Weight limit – 100kg

 

 

1-2. What are XON SNOW-1?

The SNOW-1 smart snowboard bindings are the first product in the XON series of smart sports devices. They can record, visualize and analyze your ride with real time tracking data displayed via the graphical UI of the XON smartphone app. Add a new dimension to your rides and improve your skills with XON SNOW-1.

Sensors that capture all your riding, an evolutionary form of snowboard bindings

With XON SNOW-1, 5 independent sensors can capture 13 different points of data. The load balance sensors embedded into the soles of each binding record one of the most important factors in snowboarding, two flex sensors that are attached to the board are able to detect board deflection. Furthermore acceleration, angular velocity, geomagnetism sensors are able to detect the rider’s position and direction.

Real time monitoring on your smartphone

You can connect the XON bindings to a smartphone easily via Bluetooth 4.0, real time tracking data is then visualized in the XON app, allowing you to get tips to improve your riding in real time.

GPS route mapping

By using the GPS function in your smart phone, the XON app can map your riding route. Route speed, acceleration level and gradient will be displayed with a high degree of accuracy. The extensive log data will allow you to look back over your ride history and compare performance.

Built-in ultra-high brightness LEDs

The XON bindings have ultra-high brightness LEDs built into the heel and toe. Light levels will respond to the load level sensors in each binding. You can also activate the LEDs to create impressive light trail effects in your dusk riding videos.

1-1. Box Contents

  • SNOW-1 bindings x2 (Right/Left)
  • Flex sensor ×2
  • Screws for sole-plate ×2
  • Center disc ×2
  • Center disc screw x8
  • Center disc screw washer ×8
  • Forked USB charge-cable ×1
  • Quick Setup Guide (Warranty confirmation) x 1